Spool commands



JES, JES2, JCL utilities, IDCAMS, Compile & Run JCLs, PROCs etc...

Spool commands

Postby suresh_pachwa » Thu Jun 14, 2012 11:12 pm

1). What will happen if we give 'D' infront of job in spool when the job is in execution.

2). What will happen if we give 'D' infront of job in spool for completed job.
suresh_pachwa
 
Posts: 2
Joined: Thu Jun 07, 2012 7:47 pm
Has thanked: 0 time
Been thanked: 0 time

Re: Spool commands

Postby enrico-sorichetti » Thu Jun 14, 2012 11:20 pm

what happened when You tried,
or when You did ( because You did ) read the manual or press the pf1 ( help ) key ?
cheers
enrico
When I tell somebody to RTFM or STFW I usually have the page open in another tab/window of my browser,
so that I am sure that the information requested can be reached with a very small effort
enrico-sorichetti
Global moderator
 
Posts: 2994
Joined: Fri Apr 18, 2008 11:25 pm
Has thanked: 0 time
Been thanked: 164 times

Re: Spool commands

Postby suresh_pachwa » Thu Jun 14, 2012 11:26 pm

When i tried for completed job it shows as command issued....

but i didn't get what action it took...
suresh_pachwa
 
Posts: 2
Joined: Thu Jun 07, 2012 7:47 pm
Has thanked: 0 time
Been thanked: 0 time

Re: Spool commands

Postby dick scherrer » Thu Jun 14, 2012 11:42 pm

Hello and welcome to the forum,

After you issued the 'D' command on the completed job what happened?

Was the job still in the spool?
Hope this helps,
d.sch.
User avatar
dick scherrer
Global moderator
 
Posts: 6268
Joined: Sat Jun 09, 2007 8:58 am
Has thanked: 3 times
Been thanked: 93 times

Re: Spool commands

Postby NicC » Fri Jun 15, 2012 1:50 am

What are you using to access the spool? SDSF? What were you hoping to achieve by issuing the D command?
The problem I have is that people can explain things quickly but I can only comprehend slowly.
Regards
Nic
NicC
Global moderator
 
Posts: 3025
Joined: Sun Jul 04, 2010 12:13 am
Location: Pushing up the daisies (almost)
Has thanked: 4 times
Been thanked: 136 times

Re: Spool commands

Postby Anuj Dhawan » Mon Jun 18, 2012 7:50 pm

From the manuals, under SDSF, D implies to the following:

D     Display job information in the log. You can add:     
      E    - Line, page, record, and card counts (JES3 only)
      L    - Long form (JES2 only)                         
      M    - Mains on which the job is eligible             
             to run (JES3 only)                             
      MA   - MDS allocate queue information (JES3 only)     
      ME   - MDS error queue information (JES3 only)       
      MR   - MDS restart queue information (JES3 only)     
      MSS  - MDS system select queue information (JES3 only)
      MSV  - MDS system verify queue information (JES3 only)
      MU   - MDS unavailable volumes information (JES3 only)
      SD   - DDNAMEs of all spool data sets that contain data
             (JES3 only)                                     
      SH   - DDNAMEs of data sets in spool hold status that 
             contain data (JES3 only)                       
      SP   - Spool partition name (JES3 only)               
      X    - Extended (JES3 only)                           
Anuj
Anuj Dhawan
 
Posts: 273
Joined: Mon Feb 25, 2008 3:53 am
Location: Mumbai, India
Has thanked: 6 times
Been thanked: 4 times


Return to JCL

 


  • Related topics
    Replies
    Views
    Last post