Page 1 of 2
JES2 and purge by batch
Posted:
Fri Sep 06, 2013 2:48 pm
by samb01
Hello,
i would like to purge all the job sysout with MSGCLASS=B by batch which have ten days old.
Is-it possible by batch ?
Thanks for your help.
Re: JES2 and purge by batch
Posted:
Fri Sep 06, 2013 6:02 pm
by NicC
Probably - what are you going to execute in batch? Probably SDSF? With, perhaps a Rexx wrapper?
Re: JES2 and purge by batch
Posted:
Fri Sep 06, 2013 6:28 pm
by prino
Use, if you're allowed to do so, the
JES2 $O command
Re: JES2 and purge by batch
Posted:
Fri Sep 06, 2013 7:48 pm
by Akatsukami
samb01 wrote:Hello,
i would like to purge all the job sysout with MSGCLASS=B by batch which have ten days old.
Is-it possible by batch ?
As you can see, there is a powerful and flexible Rexx/SDSF interface.
Re: JES2 and purge by batch
Posted:
Mon Sep 09, 2013 5:09 pm
by samb01
Hello,
i have an error after this command :
ADDRESS SDSF "ISFACT ST TOKEN('"TOKEN.IX"') PARM(NP P)"
Here is the error :
23 *-* /* IDENTIFIED BY THE TOKEN VARIABLE. NOTE */
24 *-* /* THE TOKEN MUST BE ENCLOSED IN SINGLE QUOTES */
25 *-* ADDRESS SDSF "ISFACT ST TOKEN('"TOKEN.IX"') PARM(NP P)"
>L> "ISFACT ST TOKEN('"
>C> "TOKEN.1"
>V> "3h4hhoSZo5KWVMNFxEBBQO5Qw0x4QGlA1IP8LEyWl4NTl1NATomihhIOIJKEQGB
>O> "ISFACT ST TOKEN('3h4hhoSZo5KWVMNFxEBBQO5Qw0x4QGlA1IP8LEyWl4NTl1
iMyxwBEQEHW1g=="
>L> "') PARM(NP P)"
>O> "ISFACT ST TOKEN('3h4hhoSZo5KWVMNFxEBBQO5Qw0x4QGlA1IP8LEyWl4NTl1
iMyxwBEQEHW1g==') PARM(NP P)"
+++ RC(8) +++
26 *-* LRC=RC
>V> "8"
Re: JES2 and purge by batch
Posted:
Mon Sep 09, 2013 5:25 pm
by prino
The error is in line 12 of your code!
Re: JES2 and purge by batch
Posted:
Mon Sep 09, 2013 7:16 pm
by samb01
How can you see that ?
I think it's a problem of right may be ?
How could i check it ?
Re: JES2 and purge by batch
Posted:
Mon Sep 09, 2013 8:10 pm
by Akatsukami
samb01 wrote:How can you see that ?
I think it's a problem of right may be ?
How could i check it ?
Display the
messages.
Re: JES2 and purge by batch
Posted:
Mon Sep 09, 2013 8:24 pm
by dick scherrer
Hello,
If after reading about the message(s) you are still stuck, you need to post the code (at least the bit that has a problem).
For diagnosing, it is often a good thing to copy the problem code into a small test script and debug.
Re: JES2 and purge by batch
Posted:
Mon Sep 09, 2013 8:33 pm
by samb01
37 *-* IF ISFMSG<>""
>V> "NOT AUTHORIZED FOR JOB"
>L> ""
>O> "1"
1 *-* THEN
38 *-* SAY "ISFMSG IS:" ISFMSG
>L> "ISFMSG IS:"
>V> "NOT AUTHORIZED FOR JOB"
>O> "ISFMSG IS: NOT AUTHORIZED FOR JOB"
ISFMSG IS: NOT AUTHORIZED FOR JOB
39 *-* /* THE ISFMSG2 STEM CONTAINS ADDITIONAL DESCRIPTIVE */
40 *-* /* ERROR MESSAGES */
thank's.
i don't what can i do to have the right ...