Page 1 of 2
TYPRUN='SCAN' not Invoked
Posted:
Fri Jul 13, 2012 9:26 am
by jaggz
Hi,
I am not able to see the Scanned Report for any JCL when I code with TYPRUN='SCAN'. Is it something the SCAN feature is missing in Z/OS ? If so, are there any equivalent features available ?
Jaggz
Re: TYPRUN='SCAN' not Invoked
Posted:
Fri Jul 13, 2012 10:25 am
by NicC
I do not understand what you mean by 'scanned report'. All TYPRUN=SCAN does is allow your JCL to be interpreted but not executed - just sent to the output queue. TYPRUN=HOLD sends it to the input queue, in hold status, after interpretation. What were you expecting? If you have no output on the output queue then you either have a JCL error in the jobcard or you have specified a MSGCLASS that prohibits the 'printing' of JCL or you have not submitted the job.
Re: TYPRUN='SCAN' not Invoked
Posted:
Fri Jul 13, 2012 12:29 pm
by BillyBoyo
I think you are thinking you are using a "JCL Checker" program: you are not.
If that is not what you are thinking, please explain more clearly and in more detail.
Re: TYPRUN='SCAN' not Invoked
Posted:
Sat Jul 14, 2012 7:38 pm
by Anuj Dhawan
What DD statement do you look at in the spool? Are you at correct one?
Re: TYPRUN='SCAN' not Invoked
Posted:
Sat Jul 14, 2012 11:21 pm
by dick scherrer
Hello,
If a TYPRUN=SCAN is run, there should be no DD statements in the spool - only the JES sysouts.
And these need to be posted here. If there are no JES sysouts, he job was flushed - probably because of an invalid JOB statement.
Re: TYPRUN='SCAN' not Invoked
Posted:
Sun Jul 15, 2012 8:00 am
by jaggz
Dear Dick,
Thanks for the clarification.
Re: TYPRUN='SCAN' not Invoked
Posted:
Sun Jul 15, 2012 8:04 am
by dick scherrer
You're welcome.
Did you fnd the "scan" information?
Re: TYPRUN='SCAN' not Invoked
Posted:
Sun Jul 15, 2012 12:08 pm
by Anuj Dhawan
If you execute a Job with TYPRUN=SCAN, you'll get the following DDName listed. As Dick say they are "JES" sysouts, I referred them as "DD-Names" as shown below:
Display Filter View Print Options Help
-------------------------------------------------------------------------------
SDSF JOB DATA SET DISPLAY - JOB JOBNAME(JOB28196) LINE 1-2 (2)
COMMAND INPUT ===> SCROLL ===> CSR
PREFIX=JOBNAME DEST=LOCAL OWNER=* SYSNAME=
NP DDNAME StepName ProcStep DSID Owner C Dest Rec-Cnt Page
JESMSGLG JES2 2 Anuj Y LOCAL 8
JESJCL JES2 3 Anuj Y LOCAL 11
one will have what you are looking for.
Re: TYPRUN='SCAN' not Invoked
Posted:
Sun Jul 15, 2012 2:10 pm
by expat
Recall something similar many moons ago and using MSGLEVEL=(1,1) on the jobcard resolved the issue
Re: TYPRUN='SCAN' not Invoked
Posted:
Sun Jul 15, 2012 2:56 pm
by NicC
Yup, all points that covered in my original reply - not bad for 6 in the morning before feeding the pigs.
EDIT - on the other hand 10:00am after feeding the pigs I had to edit this reply!