Command output not displayed in ULOG



TSO Programming, ISPF, SDF, SDSF and PDF, FTP, TCP/IP Concepts, SNA & SNA/IP etc...

Command output not displayed in ULOG

Postby Karzos » Thu Jun 25, 2015 9:52 pm

HI All,

While playing around SDSF I found something strange between our two LPARs. In our test lpar I could display a command (D NET,CPCP) and I could see its output in ULOG.
SDSF ULOG CONSOLE A041425 LINE 0 COLUMNS 20- 99
COMMAND INPUT ===> SCROLL ===> CSR
********************************* TOP OF DATA **********************************
11:16:20.85 ISF031I CONSOLE A041425 ACTIVATED
11:16:33.40 -D NET,CPCP
11:16:33.40 STC51230 IST097I DISPLAY ACCEPTED
11:16:33.41 STC51230 IST350I DISPLAY TYPE = CP-CP SESSION STATUS
IST1765I ADJACENT CP WINNER LOSER STATE
IST1766I CLK1.CDRMCLK ACT ACT UP
IST1454I 1 ADJCP(S) DISPLAYED
IST314I END
******************************** BOTTOM OF DATA ********************************

But in production lpar I could not see the whole command output.

SDSF ULOG CONSOLE A041425 LINE 0 COLUMNS 02- 81
COMMAND INPUT ===> SCROLL ===> CSR
********************************* TOP OF DATA **********************************
CKP1 2015176 11:18:34.72 ISF031I CONSOLE A041425 ACTIVATED
CKP1 2015176 11:18:38.11 -D NET,CPCP
CKP1 2015176 11:18:38.12 STC12364 IST097I DISPLAY ACCEPTED
******************************** BOTTOM OF DATA ********************************
what is restricting my production lpar in displaying the output in ulog?
"Die with memories, not with dreams"
Karzos
 
Posts: 3
Joined: Thu Jun 25, 2015 8:50 pm
Has thanked: 0 time
Been thanked: 0 time

Re: Command output not displayed in ULOG

Postby Robert Sample » Thu Jun 25, 2015 10:52 pm

Contact your site support group. SDSF commands and their output can be restricted by the site (and for each LPAR).
Robert Sample
Global moderator
 
Posts: 3720
Joined: Sat Dec 19, 2009 8:32 pm
Location: Dubuque, Iowa, USA
Has thanked: 1 time
Been thanked: 279 times

Re: Command output not displayed in ULOG

Postby NicC » Thu Jun 25, 2015 10:53 pm

Probably the sysprogs by the way they have determined which messages should be logged. This does not have to be the same for all LPARs.
The problem I have is that people can explain things quickly but I can only comprehend slowly.
Regards
Nic
NicC
Global moderator
 
Posts: 3025
Joined: Sun Jul 04, 2010 12:13 am
Location: Pushing up the daisies (almost)
Has thanked: 4 times
Been thanked: 136 times

Re: Command output not displayed in ULOG

Postby Karzos » Fri Jun 26, 2015 12:10 am

Hi Robert/NicC,

I m the sysprog for our shop. I have checked MPFLSTxx and I could not find anything regarding the suppression of these messages. Where else should I look into? Any suggestions?

Thanks
"Die with memories, not with dreams"
Karzos
 
Posts: 3
Joined: Thu Jun 25, 2015 8:50 pm
Has thanked: 0 time
Been thanked: 0 time

Re: Command output not displayed in ULOG

Postby sam_jj12 » Sun Apr 17, 2016 8:43 am

hi..

please check that you have opened same ulog session in some other panel.
this will suppress the o/p to be displayed.

*Ensure only one ULOG session is opened.
sam_jj12
 
Posts: 18
Joined: Sat Nov 21, 2015 12:02 am
Has thanked: 0 time
Been thanked: 0 time

Re: Command output not displayed in ULOG

Postby NicC » Sun Apr 17, 2016 3:17 pm

sam_jj12, you are a bit late to the party - almost a whole year. Please leave sleeping topics sleeping.
The problem I have is that people can explain things quickly but I can only comprehend slowly.
Regards
Nic
NicC
Global moderator
 
Posts: 3025
Joined: Sun Jul 04, 2010 12:13 am
Location: Pushing up the daisies (almost)
Has thanked: 4 times
Been thanked: 136 times


Return to TSO & ISPF

 


  • Related topics
    Replies
    Views
    Last post